Shark 925SS Instructions d'exploitation

Read instructions carefully before attempting to assemble, install, operate or service this pressurewasher. Failure to comply with instructions could

Page 10 Shark 925A/925SSTROUBLESHOOTING GUIDESYMPTOM POSSIBLE CAUSES CORRECTIVE ACTIONGas engine will not run. Out of gas. Replenish supply. Use only

Page 11Shark 925A/925SSIMPORTANTIf the pressure washer demonstrates other symptoms or the correctiveactions listed do not correct the problem, contact

Page 12 Shark 925A/925SSWhen ordering from your dealer, please provide the following:Model Number: 925A/925SSMachine Serial Number: __________________

Page 13Shark 925A/925SSFigure 11 - Machine Assembly, Left Side ViewRef. No. Part No. Description Qty.14 Fig. 14 Control Box Assembly 115 826167 Strain

Page 14 Shark 925A/925SSFigure 12 - Machine Assembly, Right Side ViewRef. No. Part No. Description Qty.15 Flat Washer 5/16” 716 799362 Crownlock Nut

Page 15Shark 925A/925SSFigure 13 - Machine Assembly, Top ViewRef. No. Part No. Description Qty.7 890783 Tag Gasoline Engine 18 444462 Decal Caution Ga

Page 16 Shark 925A/925SSFigure 14 - Control Box AssemblyRef. No. Part No. Description Qty.13 645990 Bridge Rectifier 114 676638 Fuse 30A 115 707146 Fu

Page 17Shark 925A/925SSFigure 15 - Coil Outlet AssemblyRef. No. Part No. Description Qty.7 Screw (4 mm x 6 mm) 18 780565 Copper Washer 29 915630 Plug

Page 18 Shark 925A/925SSFigure 16 - Coil Inlet AssemblyRef. No. Part No. Description Qty.5 754711 Tee 3/8” 16 801102 Hex Nipple 3/8” x 1-1/2” 17 87359

Page 19Shark 925A/925SSFigure 17 - Pump AssemblyRef. No. Part No. Description Qty.6 801139 Garden Hose Connector 17 856035 Garden Hose Connector Gaske

Page 2 Shark 925A/925SS WARNINGRead and observe to prevent severe personal injury or property damage.● Check hoses, fittings, wand, trigger gun andfue

Page 20 Shark 925A/925SSFigure 18 - Pump, Exploded ViewRef. No. Part No. Description Qty.7 755256 Pump Mounting Kit 18 646327 Oil Fill/Dipstick 19 814

Page 21Shark 925A/925SSFigure 19 - Fuel Tank AssemblyRef. No. Part No. Description Qty.6 309294 Nipple 3/8” Hose x 1/4” Hose 17 867368 Hose 1/4” Black

Page 22 Shark 925A/925SSFigure 20 - Trigger Gun/Dual Lance Wand AssemblyRef. No. Part No. Description Qty.7 826169 Quick Disconnect 18 915786 Quick Di

Page 23Shark 925A/925SSFigure 21 - Burner AssemblyRef. No. Part No. Description Qty.1 615850 Burner Fig. 22 12 698023 Nipple 3/8” x 1/4” Hose 13✪85108

Page 24 Shark 925A/925SSFigure 22 - Burner Parts BreakdownRef. No. Part No. Description Qty.1 919791 Fuel Pump 12 944422 Solenoid Valve 13 890906 Igni

Page 25Shark 925A/925SSFigure 23 - Wiring Diagram

SharkRWARRANTYSHARK ONE-YEAR LIMITED WARRANTY:Shark products are warranted by Shark Pressure Washers (Shark), to be free of defects in material andwor

Page 3Shark 925A/925SSFigure 1 - Machine Component LayoutDETERGENTNOZZLEPRESSURENOZZLEDUAL LANCE WANDRELIEF VALVE BURNER EXHAUST VENTTRIGGER GUNPRESS

Page 4 Shark 925A/925SSFigure 2 - Pressure Hose InstallationASSEMBLYUnpackingUnpack carefully. Wear safety glasses or goggles whileunpacking, assembli

Page 5Shark 925A/925SS2. Install the provided battery terminals as shown inFigure 5.3. To reduce the possibility of sparking attach the wiresto the ba

Page 6 Shark 925A/925SSOil BurnerBurner Air Adjustment: The oil burner on thismachine is preset for operation at altitudes below 3000feet. If operate

Page 7Shark 925A/925SSTo StartDANGER: Do not point wand or trigger gun at your-self or at any person. Bodily injury may result fromwater under high pr

Page 8 Shark 925A/925SS10. Hold wand firmly, release the trigger of the triggergun.11. Start engine. Place throttle lever in the idle position.12. Squ

Page 9Shark 925A/925SSProper Pump Care:• Do not pump acids.• Do not allow pump to run dry.• Winterize if storing in freezing temperatures, referto Sto