Shark SV780 14 Guide de l'utilisateur télécharger pdf (Page 4)

Using Your Motorized Brush

1. Make sure that the vacuum is in the

"Off" position.

2. Firmly insert the

motorized brush

(Fig. 10) into the

air-intake nozzle

of the dust cup

container ensuring

that the contact

pins are

engaged in the

connector slots

of the unit. (Fig. 11)

Note: This motorized brush is for

vacuuming short pile carpets, rugs

or upholstery.

WARNING: Do not touch the

motorized brush while it is in motion.

3. To attach the

crevice tool or the

dusting brush to

the hand vacuum,

push the

attachment into the

suction hole in the

front of the dust

container.

(Fig. 8 & Fig. 9)

CAUTION: The

suction inlet must

be open and free of any obstructions at

all times. Otherwise, the motor will

overheat and could become damaged.

Fig. 10

Fig. 11

Metal

contact

pins

Dust Cup

Release

Button

Fig. 6

OPERATING INSTRUCTIONS

Assembly

Note: The filter must always be used

when operating the hand vacuum.

1. To open the dust cup container,

press the dust cup release button

and remove the dust cup container.

(Fig. 6)

2. Verify that the filter is inside, then

reattach the dust cup container to

the hand vacuum. (Fig. 7)

Fig. 7

Fig. 8

Using Your Cordless Vacuum

1. Unplug unit from charger.

2. To start the unit, slide the "On/Off“

switch to the "On" position.

3. To stop the hand vac, slide the

"On/Off" switch to the "Off" position.

4. A crevice tool is provided for

cleaning narrow, hard to reach

places. A dusting brush is provided

for cleaning upholstery, furniture,

etc. A motorized brush is provided

for cleaning low pile carpets or

upholstery. A floor to carpet brush

is provided for cleaning floors and

carpets.

Changing & Cleaning the Filter

To achieve the best performance,

empty the dust cup container and

clean the filter after each use.

1. To remove the dust cup container,

press down on the dust cup release

button and pull off the dust cup

container.

2. Pull out the filter.

3. Empty the dust

from the dust cup

container.

(Fig. 12)

4. Rinse the filter in

cold water, and then wait until it air

dries completely before replacing it

back into the dust cup container.

Do not use a washing machine to

clean the filter. Do not use a hair

dryer to dry it. Air dry only.

CAUTION: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will

overheat and could become damaged.

WARNING: Always empty the dust

cup container and clean the filter before

each use and during prolonged usage.

Never over fill the dust cup (container) -

remove dirt and clean the filter and

frequently during prolonged usage or

risk motor damage.

If you wash the filter, make sure that

it is completely air dry before

inserting back in the vacuum.

Note: The filter is washable. It should,

however, be replaced every three (3) to

six (6) months, depending on usage to

ensure peak performance of your

vacuum.

Fig. 12

OPERATING INSTRUCTIONS

Please Note: The filter is washable. It should, however, be replaced every three

(3) months to ensure peak performance of your vacuum.

Important: Make sure that filter has completely air dried before

re-installing back in the hand vacuum.

REPLACEMENT PARTS

Replacement dust cup filter SKU# XF769

Replacement battery pack SKU# XBT779

To order replacement batteries or filters or for technical support:

Call: 1 (800) 798-7398

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

visit our website: www.sharkclean.com

Fig. 9

TROUBLESHOOTING GUIDE

PROBLEM

POSSIBLE REASON

POSSIBLE SOLUTION

HAND VACUUM

WILL NOT

OPERATE

1. Batteries discharged.

2. No power in electrical

outlet supplying

transformer.

1. Charge unit.

2. Check fuse or

breaker. Replace

fuse/reset breaker.

HAND VACUUM

WILL NOT PICK-

UP OR SUCTION

POWER IS WEAK

1. Dust cup container is

full.

2. Filter needs cleaning

or replacement.

3. Unit needs

recharging.

1. Empty dust cup

container.

2. Remove filter and

check for object(s) in

air duct and remove.

Clean or replace filter.

3. Charge unit.

MOTORIZED

BRUSH WILL

NOT WORK

1. The 2 metal pins of

the motorized brush

are not in contact

with the vacuum

cleaner.

2. Motorized brush is

clogged up.

1. Firmly insert the

motorized brush into

the air-intake nozzle.

This will connect the

motorized nozzle to the

unit power supply.

2. Remove all lint, hair

etc. from motorized

brush.

DUST ESCAPING

FROM HAND

VACUUM

1. Dust cup container is

full.

2. Filter is not installed

correctly.

3. Puncture/hole in

filter.

1. Empty dust cup

container.

2. Review the filter

installation

instructions.

Replace the filter.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Shark SV780 14 Guide de l'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Aspirateurs Shark SV780 14