Shark V1950 N Guide de l'utilisateur télécharger pdf (Page 4)

6 TOLL FREE: 1-800-798-7398 7ww w.sharkclean.com

ASSEMBLY OF YOUR FLOOR

AND CARPET CLEANER:

NOTE: The charging adapter

will be shipped inside the foam

packaging.

1 Slide the upper pole (the tube

with the handle) into the end

of the Shark

®

Backsaver

™

joint

that has a small notch in it (a).

Then slide the lower pole into

the other end of the joint (b).

Push it in until it clicks into

place. (Fig. 1)

COMPONENTS:

A Main Unit

B Speed Control Button

C Power Button

D Dust Container

E Backsaver

™

Release Button

F Upper Pole with Handle

G Shark

®

Backsaver

™

Joint

H Lower Pole

I Dust Container Empty Button

J Charging Adapter

Fig. 1 Fig. 2

E

I

ASSEMBLY

F

G H

J

2 Insert the Shark

®

Backsaver

™

folding handle you just

assembled into the top of the

unit. You should hear the

locking tab click into place.

(Fig. 2)

IMPORTANT: You must charge

the batteries for 24 hours before

using the unit for the ﬁrst time.

See page 7 for instructions on

charging your unit.

C

A

B

D

Model Number: V1950 N 32

Voltage: 7.2 V

If the brush roll stops moving, it’s probably due

to the anti-jam feature. This feature protects

the motor from becoming overheated. If the

brush becomes overloaded, it will stop turning

and both speed indicator lights will stay on.

Turn off your unit by pressing the power button

once. See page 9 for instructions on removing

or cleaning the brush roll. Wait for 10 seconds

to let your unit cool down. Now press the

power button again and you’re ready to resume

cleaning!

NOTE: Charge the batteries for

24 hours before ﬁrst use.

1 Always make sure that the unit

is turned off. (Fig. 3)

2 Insert the charger plug into the

hole on the side of the unit.

Plug the charger into a wall

outlet. The light next to the

power button will illuminate

when the unit is charging. If the

unit is plugged in and the light is

not illuminated, press the power

button once. The light should

now be illuminated indicating

that the unit is charging.

(Fig. 4)

CHARGING YOUR CORDLESS FLOOR AND CARPET CLEANER

3 After ﬁrst use, recharge for 16

hours. Your cordless ﬂoor and

carpet cleaner is powered by

Ni-Cd batteries that need this

time to build up their charge.

4 Always remove the charging

adapter from the unit after the

charging period has completed.

Storing the unit with the

adapter attached and

plugged in will reduce the

battery life.

IMPORTANT: Although many

adaptors look similar, it’s

important to use only the

adaptor that came with the unit

(KA12D090015023U).

To maintain peak

performance of your cordless

ﬂoor and carpet cleaner,

let the battery run down

completely at least once a

month and then recharge it.

indicates the speed optimized to

clean bare ﬂoors and two lights

indicate the speed optimized to

clean carpets and larger debris

on bare ﬂoors. (Fig. 6)

1 Press the power button to start

the unit. The lights on the unit

will illuminate. When ﬁnished

cleaning, press the power

button again to turn the unit

off. (Fig. 5)

USING YOUR CORDLESS FLOOR AND CARPET CLEANER

2 You can adjust the speed of the

brush roll to suit the ﬂoors that

you are cleaning. Press the

button on the right (opposite

the power button) to switch

between speeds. One light

Fig. 3

Fig. 4

Fig. 5

Fig. 6

FLOOR CARPET

OFF

a

b

V1950_N_32_ENG_IB_100928.indd 6-7 28/09/10 4:21 PM

1 2 3 4 5 6 7

Commentaires sur ces manuels

Pas de commentaire