Shark CB-353007B Manuel de l'opérateur télécharger pdf (Page 9)

9.800-086.0 • Rev. 3/09

PRESSURE WASHER

OPERATOR’S MANUAL

PRESSURE WASHER

WARNING: Some detergents

may be harmful if inhaled or

ingested, causing severe nau-

sea, fainting or poisoning. The

harmful elements may cause

property damage or severe

injury.

STEP 1: Use detergent designed

speciﬁcally for pressure washers.

Household detergents could dam-

age the pump. Prepare detergent

solution as required by the manu-

facturer. Fill a container with pres-

sure washer detergent. Place the

ﬁlter end of detergent suction tube

into the detergent container.

STEP 2: Apply safety latch

to spray gun trigger. Secure

black detergent nozzle into

quick coupler. NOTE: Deter-

gent cannot be applied using

the Yellow nozzle.

STEP 3: With the motor run-

ning, pull trigger to operate

machine. Liquid detergent is

drawn into the machine and mixed with water. Apply

detergent to work area. Do not allow detergent to dry

on surface.

IMPORTANT: You must ﬂush the detergent injection

system after each use by placing the suction tube

into a bucket of clean water, then run the pressure

washer in low pressure for 1-2 minutes.

THERMAL PUMP PROTECTION

If you run your pressure washer for 2 minutes without

pressing the trigger on the spray gun, circulating water

in the pump can reach high temperatures. When the

water reaches this temperature, the pump protector

engages and cools the pump by discharging the warm

water onto the ground. This thermal device prevents

internal damage to the pump.

CLEANING TIPS

Pre-rinse cleaning surface with fresh water. Place

detergent suction tube directly into cleaning solution

and apply to surface at low pressure (for best results,

limit your work area to sections approximately 6’ square

and always apply detergent from bottom to top). Allow

detergent to remain on surface 1-3 minutes. Do not

allow detergent to dry on surface. If surface appears

to be drying, simply wet down surface with fresh water.

If needed, use brush to remove stubborn dirt. Rinse at

high pressure from top to bottom in an even sweeping

motion keeping the spray nozzle approximately 1’ from

cleaning surface. Use overlapping strokes as you clean

and rinse any surface. For best surface cleaning action

spray at a slight angle.

Recommendations:

• Before cleaning any surface, an inconspicuous

area should be cleaned to test spray pattern and

distance for maximum cleaning results.

• If painted surfaces are peeling or chipping,

use extreme caution as pressure washer may

remove the loose paint from the surface.

• Keep the spray nozzle a safe distance from the

surface you plan to clean. High pressure wash

a small area, then check the surface for dam-

age. If no damage is found, continue to pressure

washing.

CAUTION - Never use:

• Bleach, chlorine or other corrosive chemicals

• Liquids containing solvents (i.e., paint thinner,

gasoline, oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the machine and will dam-

age the surface being cleaned.

RINSING

It will take a few seconds for the detergent to clear.

Apply safety latch to spray gun. Remove black soap

nozzle from the quick coupler. Select and install the

desired high pressure nozzle. NOTE: You can also stop

detergent from ﬂowing by simply removing detergent

siphon tube from bottle.

WARNING

DETERGENTS AND GENERAL OPERATING TECHNIQUES

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Shark CB-353007B Manuel de l'opérateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Pulvérisateur de peinture Shark CB-353007B